"Love the rotary and the whole system. It changed the way I look at cutting fabric."
– Debbie, verified customer
Most cutting trouble is not one problem. The blade starts to skip, so you press harder. You press harder, so the ruler creeps. The ruler creeps, so the block leaves the mat a sixteenth short, and you square it up and lose the point on the star.
Three tools, one job. That is why they are on one page, at half price.
How the three work together
The cutter comes with a removable TrueCut® guide. It locks into the raised track that runs along both sides of the ruler, so the blade follows the edge instead of wandering off it, and the ruler stops sliding under your hand halfway down a long cut. Prefer the rulers you already own? Take the guide off and it works like any rotary cutter.
The blades
Every blade is titanium coated SKS-7 tungsten steel. The coating is harder than the steel underneath and it cuts friction at the edge, so the edge holds its shape long after an uncoated blade has rounded off. That is why these blades last 6 times longer than a standard brand-name blade. It is not a slogan. It is what the coating does.
Ten in the box, because a blade only helps you on the day it is sharp. You change it the moment it starts to skip, not four days later when the delivery van arrives.
The cutter
The handle is straight, so the cutter lines up with your forearm and you push through the cut instead of angling into it. Textured side grips stop it turning in your hand on a long pass. The blade sits further out of the housing than on most cutters, which means you can see the line you are cutting and the edge bites through the layers instead of riding over them.
Blade changes take seconds. Press the button, the magnetic quick-release lets go, and the new blade drops in. No screw, no washer, no small parts on the floor. It takes any standard 45mm blade, not only ours.
The ruler
Six and a half inches square, the size you reach for most: squaring up blocks, trimming half-square triangles and flying geese, cutting the small shapes that decide whether the points meet. The grid reads in eighth-inch increments, the quarter, half and three-quarter lines are labeled, and there is a 45° line for trimming on the bias. Marking holes let you mark the fabric through the ruler without moving it. It is injection-molded thermoplastic rather than standard acrylic, so the edges stay straight and chip-resistant through years of cutting.
In the box
- 10 x 45mm titanium coated rotary cutter blades, in a plastic storage container
- 1 x Straight Cutter 45mm (Quick Release) with removable TrueCut® guide
- 1 x TrueCut® 6.5" x 6.5" Square Quilting Ruler
Specifications
- Blades: 45mm, round center hole, the standard fit for rotary cutters
- Blade steel: titanium coated SKS-7 tungsten steel
- Cutter: 45mm straight handle, magnetic quick-release blade change, textured side grips, removable TrueCut® guide, fits most 45mm blade brands
- Ruler: 6.5" x 6.5", 1/8" grid, 45° line, marking holes, chip-resistant thermoplastic
What it comes to
| 10 x 45mm titanium coated blades |
$75.00 |
| Straight Cutter 45mm (Quick Release) |
$38.00 |
| TrueCut® 6.5" x 6.5" Square Ruler |
$20.00 |
| Bought separately |
$133.00 |
| All three together, 50% off |
$66.50 |
Half price on all three. The bundle costs less than the ten blades cost on their own page, and the cutter and the ruler come in the same box.
60 day satisfaction guarantee. Cut with the blades for two months. If you find a blade that beats ours, tell us and we refund you in full. Keep the blades.
Put a fresh blade in the cutter, lock the guide into the ruler track, and make one pass. That is the whole argument, and it takes about four seconds.
