Most cutting trouble is not one problem. The blade starts to skip, so you press harder. You press harder, so your wrist takes the load. Your wrist takes the load, so the ruler creeps, and the block leaves the mat a sixteenth short. You square it up and lose the point on the star.
Four tools, one job. This is our cutting bundle built around the 28mm ergonomic cutter, for anyone who cuts for hours at a time or whose hands complain afterward. The ruler in this one is the 6.5 x 12.5 inch, the long one for strips and binding.
How the four work together
The cutter comes with a removable TrueCut® guide. It locks into the raised track that runs along both sides of the ruler, so the blade follows the edge instead of wandering off it. The TrueGrips go on the underside of the ruler and stop it from sliding under your hand halfway down a long cut. With a sharp blade you never have to lean on any of it. Prefer the rulers you already own? Take the guide off and the cutter works like any rotary cutter, and the grips stick to those rulers too.
The cutter, and why this one is different
The 28mm My Comfort Ergo Cutter is built around the Comfort Curve Grip. Instead of a straight handle that asks your wrist to bend, the curve lines up wrist, arm and shoulder so the cutting force sits directly over the blade. Less strain per cut, and small detailed cutting is exactly where a tired wrist shows.
The 28mm is the small wheel, for curves, appliqué shapes and detailed cutting. A smaller wheel turns inside a tighter radius, so it follows the line you drew instead of running wide. There is an easy-to-use blade guard for when it goes back in the drawer, and the cutter works for right or left handed use.
One detail that has nothing to do with cutting and that people like anyway: the handle takes customizable inserts, so you can put a scrap of your favorite fabric or a photo behind the panel.
The blades, the part that wears out
A dull 28mm shows itself faster than any other size. The wheel meets the fabric over a short contact patch, so when the edge goes it stops cutting and starts pushing the fabric ahead of it, and on a curve that is exactly where the shape goes wrong. That is the whole argument for keeping sharp ones within reach.
Every blade is titanium coated SKS-7 tungsten steel. The coating is harder than the steel underneath and it cuts friction at the edge, so the edge holds its shape long after an uncoated blade has rounded off. That is why these blades last far longer than regular blades. It is not a slogan. It is what the coating does.
Ten in the box, because a blade only helps you on the day it is sharp. You change it the moment it starts to skip, not four days later when the delivery van arrives.
The ruler
Six and a half by twelve and a half inches. Long enough for strips and binding, short enough to move around the mat, and a natural fit for fat quarters. The extra half inch gives you a seam allowance reference on one side. The grid reads in eighth-inch increments with labeled quarter and three-quarter marks, and there are 30°, 45° and 60° lines for angled cuts. Marking holes let you mark the fabric through the ruler without moving it, and the injection-molded thermoplastic resists chipping.
The TrueGrips
Small clear rings that stick to the underside of a ruler. They hold it where you put it without marking the fabric or the mat, and they are thin and clear enough that you forget they are there: the ruler sits flat and the markings stay readable. The pack has more than one size, so there are enough left over for the rulers you already own.
In the box
- 1 x TrueCut® 28mm My Comfort Ergo Cutter with removable TrueCut® guide
- 10 x 28mm titanium coated rotary cutter blades, in a plastic storage container
- 1 x TrueCut® 6.5" x 12.5" Rectangle Quilting Ruler
- 1 x TrueCut® TrueGrips™ Non-Slip Ruler Grips
Specifications
- Cutter: 28mm My Comfort Ergo, Comfort Curve Grip, blade guard, right or left handed use, removable TrueCut® guide, customizable handle inserts, compatible with many popular blade brands
- Blades: 28mm, round center hole, the standard fit for rotary cutters
- Blade steel: titanium coated SKS-7 tungsten steel
- Ruler: 6.5" x 12.5", 1/8" grid, 30°, 45° and 60° lines, seam allowance reference on one side, marking holes, chip-resistant thermoplastic
- TrueGrips: clear, thin, peel-and-stick non-slip grips in more than one size, for any quilting ruler
The cutter and the ruler are the tools that last. The blades are the part you use up, and that is why there are ten of them.
60 day satisfaction guarantee. Cut with the blades for two months. If you find a blade that beats ours, tell us and we refund you in full. Keep the blades.
Put a fresh blade in the cutter, lock the guide into the ruler track, and make one pass. That is the whole argument, and it takes about four seconds.
