TrueCut Cutting Bundle, 45mm My Comfort Ergo Cutter, 10 Titanium Blades, 3 x 8 inch Rectangle Ruler and TrueGrips

Most cutting trouble is not one problem. The blade starts to skip, so you press harder. You press harder, so your wrist takes the load. Your wrist takes the load, so the ruler creeps, and the block leaves the mat a sixteenth short. You square it up and lose the point on the star.

Four tools, one job. This is our cutting bundle built around the 45mm ergonomic cutter, for anyone who cuts for hours at a time or whose hands complain afterward. The ruler in this one is the narrow 3 x 8 inch, for strips and trimming.

How the four work together

The cutter comes with a removable TrueCut® guide. It locks into the raised track that runs along both sides of the ruler, so the blade follows the edge instead of wandering off it. The TrueGrips go on the underside of the ruler and stop it from sliding under your hand halfway down a long cut. With a sharp blade you never have to lean on any of it. Prefer the rulers you already own? Take the guide off and the cutter works like any rotary cutter, and the grips stick to those rulers too.

The cutter, and why this one is different

The 45mm My Comfort Ergo Cutter is built around the Comfort Curve Grip. Instead of a straight handle that asks your wrist to bend, the curve lines up wrist, arm and shoulder so the cutting force sits directly over the blade. Less strain per cut, and the difference shows up on the long sessions rather than the short ones.

45mm is the size most quilters use for most things: yardage, strips, trimming blocks, a few layers at once. The blade sits further out of the housing than on most cutters, so you can see the line you are cutting and the edge bites through the layers instead of riding over them. Blade changes are push-button quick release: press, the old blade comes out, the new one drops in. No screw, no washer, no small parts on the floor. There is an easy-access safety lock for when it goes back in the drawer, and the whole cutter converts for right or left handed use.

One detail that has nothing to do with cutting and that people like anyway: the handle takes customizable inserts, so you can put a scrap of your favorite fabric or a photo behind the panel.

The blades, the part that wears out

Every blade is titanium coated SKS-7 tungsten steel. The coating is harder than the steel underneath and it cuts friction at the edge, so the edge holds its shape long after an uncoated blade has rounded off. That is why these blades last far longer than regular blades. It is not a slogan. It is what the coating does.

Ten in the box, because a blade only helps you on the day it is sharp. You change it the moment it starts to skip, not four days later when the delivery van arrives.

The ruler

Three inches by eight, the narrow ruler that lives next to the mat. Trimming binding, cutting strips, squaring up small units, the quick correction before a block goes together. The narrow width keeps it light and easy to handle, and you can see past it on small pieces where a wide ruler hides the fabric. The markings and grid lines are easy to read, and it is built to resist chipping.

The TrueGrips

Small clear rings that stick to the underside of a ruler. They hold it where you put it without marking the fabric or the mat, and they are thin and clear enough that you forget they are there: the ruler sits flat and the markings stay readable. The pack has more than one size, so there are enough left over for the rulers you already own.

In the box

• 1 x TrueCut® 45mm My Comfort Ergo Cutter with removable TrueCut® guide
• 10 x 45mm titanium coated rotary cutter blades, in a plastic storage container
• 1 x TrueCut® 3" x 8" Rectangle Quilting Ruler
• 1 x TrueCut® TrueGrips™ Non-Slip Ruler Grips

Specifications

• Cutter: 45mm My Comfort Ergo, Comfort Curve Grip, extra blade exposure, push-button quick release, safety lock, converts for right or left handed use, removable TrueCut® guide, customizable handle inserts, compatible with many popular blade brands
• Blades: 45mm, round center hole, the standard fit for rotary cutters
• Blade steel: titanium coated SKS-7 tungsten steel
• Ruler: 3" x 8", easy-to-read markings and grid lines, chip-resistant construction
• TrueGrips: clear, thin, peel-and-stick non-slip grips in more than one size, for any quilting ruler

The cutter and the ruler are the tools that last. The blades are the part you use up, and that is why there are ten of them.

60 day satisfaction guarantee. Cut with the blades for two months. If you find a blade that beats ours, tell us and we refund you in full. Keep the blades.

Put a fresh blade in the cutter, lock the guide into the ruler track, and make one pass. That is the whole argument, and it takes about four seconds.